Видео

Sure you can 😊

Very welcome 😊

www.windowlink.com/

Hi, yes it can 👍

Hi, you can adjust the door via the hinge adjustment or re-pack the glazing to pull the door back into alignment.

Hi. I'm in the same situation. I'm gonna replace mine but for the time being, I'm using the pole that goes in the middle part with pliers to manually lock and open the window 😂

Very welcome 🤗

Can you elaborate on interlock ?

@@DGPSUK ruclips.net/user/shortsSY9tFDVFp9A?si=j_E0182fc6jMf-RK the top groove that fits into the frame.

Around 2-3 months but everyone is different.

Snap shot... ruclips.net/user/shorts3o8KkfGXF_0?si=mXvdrxlbq_CmqEBb

Hi, could you email us some images and we can see if we can help sales@dgpsuk.com

Very welcome 😊

Hi, unfortunately not as they are fixed in there solid, sorry.

To gain easier access to repair the window when the lock has failed.

Hi, it doesn't but we do offer a similar restrictor which does... www.double-glazing-parts-spares.co.uk/Hold-Open-Door-Restrictor

Very welcome 😊

Hi, it could be the spindles have worn or the actual locking mechanism is broken, try a good handle in a window that doesn't work to see which is the issue. Send some images over to sales@dgpsuk.com for lock identification if you find it's the lock, but yes easier to replace the whole handle rather than the spindles themselves. Regards Steven

@@DGPSUK thanks for the reply. Do you need any pictures in particular?

@@DGPSUK hi there, I’ve emailed some pics over to you now, I think it could be the locking mechanism!

Thank you for the great info, 😊😊

Hi what size do you need. Steven

Very welcome and thank you for commenting 😊

Hi, could you send an image of the issue to sales@dgpsuk.com 😊

Yes they are 😊

@DGPSUK thank you 😂 I didn't know if they were clip once and that's it. I managed to get it off and back on. Thanks again

@@MissMalikaA yes exactly although some suppliers super glue them on 🙄

Hi, if you need any extra close up shots of a certain detail just let me know 👍 all feedback welcome 🤗

Hi, can you see the screws?, send me some images to sales@dgpsuk.com

@@DGPSUK Hi, many thanks will have a closer look tomorrow.

@@Theflowoflove it could be the type where you need to remove the glass pane to get to the screws, some companies do it that way to conceal the screws.

@@DGPSUK Thank you so much. You are very helpful. BR

@@Theflowoflove absolutely no problem at all 😊 always happy to help

Thank you 😊

Hi send me an image to sales@dgpsuk.com

@@DGPSUK I managed it in the end! However, I appreciate your swift response! Thank you

@@steveaga4683 excellent 👌 and very welcome

@@DGPSUK As I said, I managed to remove the handle, but I still can't get the mechanism to work. Window is still shut in the partially open stage! Looks like the whole mechanism inside the window is buggered!

@@steveaga4683 can you email me an image of the lock and I'll identify it for you 👍

Many thanks, means a lot. I do these at the weekend on request and a few extra videos of what i think would help people 😊 so these comments make it all worthwhile. Thank you

These are non handed so suit both ways. Normally handed handles are a cranked shape.

​@DGPSUK I had a daft question - bought a universal handle. I want to open to left, so locked when inline with the mechanism (down) and left and open. Atm it is going to the top to open. Is it upside down? How does it 'know' which way around it is working? Do I need to spin the spindle? Sorry daft I know.

@@lucylindsay3442 Hi are you installing the handle different to what it was originally, if so you need to remove the lock and reverse it, you will also need to move the locking keeps. Let me know if you would like a video done to show what I mean. 👍

Thank you - definitely was being daft but I finally have a replaced handle. V. V. Helpful video (although cutting the screws was also 'fun').

Hi, yes it's fairly common for the spindles to get stuck in the locks, we see it a lot in our coastal area due to the salt air. The spindle should be long enough to just pop out the other side of the lock when installed.

Yes that works well to stick it down 👍 or even a decent silicone 👍

Yes we do

We don't have one at present but I'll put it on my list...This may help ruclips.net/video/8RoRI9wQPm4/видео.htmlsi=wX0imY6FC4JaOHLv

Hi, we use 3.9 x 32mm

are they self drilling@@DGPSUK

@@aldavis2692 yes self drilling as there should be reinforcement in the frames 👍

I can only dfind 4mmx 32 will these do @@DGPSUK

@@DGPSUK are the measurements the same for 90 degree oppening 110 from edge thank you

Hi, we prefer to reinforce all our windows, some companies only use it at certain lengths as you mention, more so with white. All colour/foiled frames should be reinforced.

thanks a million @@DGPSUK

@@jovandesmond8319 no problem at all 👍👍👍

@@DGPSUK do you know the cost of upvc profile systems from suppliers ? cost per tonne or length ?

@@jovandesmond8319 all suppliers/extruders price differently, we have our own tailored price list from our profile supplier.

Hi, we can supply them but only in Chrome, they were discontinued around 8 years ago.

Very welcome 😊

Ah yes not so easy 😞

@@DGPSUK Thanks for the great vid, I managed to get a torch down the wall to see things and now the key turns like silk 👍🏽

@@ChrisTheSparky excellent I'm glad these videos help, even just to point anyone in the right direction 😊

We no longer manufacture our own glass, it's all bought in ready made but there are very many options of glass to choose from. We did hand cut all of our glass. The standard DGU we use is: 4/20/4 (28mm overall) 4mm clear float 20mm warm edge spacer bar 4mm clear float Low e Argon filled

@@DGPSUK what's tools do you use for cutting the 4mm float glass ?

@@jovandesmond8319 diamond tipped cutter and a long set square designed for glass

Hi, I don't believe there is such a thing as teaching sessions for specifically fabrication, but you could maybe try offering a company some of your free time in a factory that manufactures windows and doors to gain extra knowledge 🤷

Hi, not one that I've seen but I suppose you could easily rig up a small template and use an 8mm & 10mm drill bit

@@DGPSUK ok thanks 👍🏿

Hi, we manufacture both options welded and mechanically jointed. I personally prefer the mechanically jointed look 👍

Hi, it will stop the door going by 90 degrees but doesn't hold the door open.

Hi it does vary, have a look at the following... www.norrsken.co.uk/newsitem/trickle-vents-guidance-ventilation-part-f#:~:text=HOW%20MANY%20TRICKLE%20VENTS%20DO,has%20more%20than%20one%20bedroom.

Thank you @@DGPSUK

Excellent 👌👍 thank you for commenting

Cheers really appreciate the kind words 😊 just happy to help